9TURBO RC SOUND-MINI is sound module for RC electric car.
This sound module will generate engine sound that synchronize with transmitter trigger/stick throttle proportional control.
+ Micro controller operation @ frequency 48Mhz.
+ board size 2.0cm x 4.0cm
+ onboard sound data chip 1024kbit non-volatile.
+ Sound data can upload from computer/notebook via USB port.
+ when loaded with Gasoline sound, it have 2 mode select by switch #3 for Rally or Drift
+ when loaded with Diesel sound, it have 2 mode select by switch #3 for General or Crawler
+ use only 2ch from RC receiver for control all functions.
+ RX Ch1 get steering signal for control horn sound, Tyre effect sound, Lamp functions
+ RX Ch2 get throttle signal for control engine and effect sound, brake and reverse lamp
+ Audio Line-out, jack 3.5mm for use with general MP3 amplifier speaker.
+ DC input 5V to 6V , get from ESC signal cord or receiver battery pack
+ I2C port for connect with LIGHT-MINI (LIGHT-MINI not include)
+ when use with LIGHT-MINI can control lamps front, fog, Tail/Brake, Reverse, Turn, Emergency, AUX1, AUX2
SOUND-MINI , Small board size only 2cm x 4cm.
Designed for easy to install and uses.
it need only 2 channel of receiver (ST & TH) for full operation.
and no need to use Y-cable.

Audio line-out can use with general MP3 amplifier speaker
that have LINE-IN or AUX.

SOUND-MINI wiring with RC electric system



Loaded with Diesel engine sound
Switch #3 select mode General or Crawler


Loaded with Gasoline engine sound
Switch #3 select mode Rally or Drift


Upload engine sound data to SOUND-MINI


SOUND-MINI work with LIGHT-MINI operation

click for enlarge 9TURBO RC SOUND-MINI KIT
+ 9TURBO RC SOUND-MINI board
+ 2 servo wire 10cm
+ 1 Audio Line-out wire 10cm with female jack 3.5mm

Software for update engine sound data
Please read this page http://soundrc.com/mini/PC

9TURBO RC LIGHT-MINI is light system module for RC electric car.
This LIGHT-MINI working with SOUND-MINI, connect via I2C cord.
for control lamps front, fog, Tail/Brake, Reverse, Turn, Emergency, AUX1, AUX2
+ board size 2.0cm x 4.0cm
+ I2C port for connect with SOUND-MINI
+ 8 channels lamp control
+ Lamp output 5 volt 100mA max per channel
+ DC input 7V to 9V , Li-Po 2S 7.4V recommend *

Board PIN-OUT

 

LIGHT-MINI connect to SOUND-MINI via I2C cord


when use with main battery Li-Po 2S 7.4V
DC input can direct connect to main battery


when use with main battery Li-Po 3S 11.1V
DC input need external small battery Li-Po 2S 7.4V

click for enlarge 9TURBO RC LIGHT-MINI KIT
+ 1 x 9TURBO RC LIGHT MINI board
+ 1 x Servo wire 10cm (use as I2C wire)
+ 1 x Power wire 30cm
+ 1 x Lamp#1 set : Front 2 white LED 5mm, with wire 30cm + 30cm
+ 1 x Lamp#2 set : Fog/Flash 2 white LED 5mm with wire 30cm + 30cm
+ 1 x Lamp#3 set : Tail/Brake 2 red LED 5mm with wire 30cm + 30cm
+ 1 x Lamp#4 set : Reverse 2 snow LED 5mm with wire 30cm + 30cm
+ 1 x Lamp#5 set : Turn left 2 yellow LED 3mm with wire 30cm + 45cm
+ 1 x Lamp#6 set : Turn right 2 yellow LED 3mm with wire 30cm + 45cm
+ 1 x Lamp#7 set : Aux1 with wire 30cm
+ 1 x Lamp#8 set : Aux2 with wire 30cm
+ 1 x 5 white LED 5mm and 5 resistor 10 ohm use for Aux1/Aux2

RC SOUND-MINI & RC LIGHT-MINI was designed by Mr.Smith Vorapatratorn 9TURBO.COM | Facebook Page